Planual Explained - Day 8

Highlighted
Master Anaplanner/Community Boss

Planual Explained - Day 8

“Rule 1.07-02”: Article 1, Chapter 7, and Rule 2 – “Version line item subsets”. Use line item subsets to create different numeric formulae to avoid multiple ifs. It goes against Performance, Logical elements of PLANS if you wish to use multiple if statements.

Use Case: Based on the user defined months we want to compare the values for KPI metrics for selected months.  Metrics such as Revenue, Gross Profit, Salary, Operating Expenses and Non-Operating Expenses are calculated in different modules and share the common dimensionality (Country)

Note: Revenue and Gross Profit are calculated in Revenue Module

          Salary and Operating Expenses are calculated in Employee Expenses Module

         Non Operating Expenses are calculated in Other Expenses Module

Here is how it was done in Pre Planual Era:  

Source Modules: Revenue Module, Employee Expenses Module, Other Expenses Module, Select Months Module

Misbah_0-1589457838241.png

We used to create a module with following artifacts

Dimensions of Target Module: Country, Users and Metrics

Line items: Month 1, Month 2 and Delta

 

Formula in Month 1

Misbah_1-1589457838266.png

 

Formula in Month 2

Misbah_2-1589457838292.png

 

What is wrong with this method? It is considered to be a very complex formula because Anaplan Engine has to check each condition to return the corresponding value – thus impacting the performance. Logically also it makes no sense to take the long route when you have a shorter route available.

Here is how it should be done in Planual Way:  Here is a step by step guide

Step 1: Create a Line item Subset based on Revenue, Employee Expenses and Other Expenses Modules. Enable all those line items in the LIS required here

Misbah_3-1589457838296.png

 

Step 2: Create LIS staging module which will pull the information from all three source modules by using COLLECT() function. This module will be dimensioned by Country, LIS and Time

Misbah_4-1589457838303.png

 

Step 3: Create a System mapping module dimensioned by Metrics List and insert a line item formatted as LIS

Misbah_5-1589457838308.png

 

Step 4: Create a module dimensioned by Metrics, Country and Users. Insert three line items i.e., Month 1, Month 2 and Delta

 Formula in Month 1:

Misbah_6-1589457838314.png

 

Formula in Month 2:

Misbah_7-1589457838321.png

 

 

Note that there are two LOOKUPs in the formula. Although this is far better than IF ELSE statements it is still doing transformations before the output is given. So let’s try to get rid of one extra lookup

Step 4(a): Create a module dimensioned by LIS, Country and Users. Insert three line items i.e., Month 1, Month 2 and Delta

Formula in Month 1:

Misbah_8-1589457838331.png

 

Formula in Month 2:

Misbah_9-1589457838338.png

 

Only difference between Step 4 and Step 4(a) is one of its dimensions. Step 4 has Metrics as a dimension and Step 4(a) has LIS as a dimension.

 

2 REPLIES 2
Highlighted
Valued Contributor

Re: Planual Explained - Day 8

Good Morning @Misbah 

What do you think is the reason for including the Users list in some of the example modules?
Is it to allow the Anaplan Engine to use multi-threads or there is another reason pertaining to this specific situation?

Einas
"Give a Man a Fish, and You Feed Him for a Day. Teach a Man To Fish, and You Feed Him for a Lifetime"
Highlighted
Master Anaplanner/Community Boss

Re: Planual Explained - Day 8

@einas.ibrahim 

 

Good morning!

 

Not a blanket rule. Here the User is going to make the selections of the months in "Select your Month" module and it should not override other users' selection hence the need for Users dimension