I do not seem to be seeing the 1st Forceast Year as a line item in my SYS01 Time Settings by week module. Could someone assist me with what the problem could be?
Hi @PAmoak
Could you share the screenshot also?
Thanks
Hello @PAmoak ,
If the issue is that you cannot find the line item, it could be because you need to create it.
If the issue is that you do not know how to get to the solution, @Misbah provided a response in this link - please find below through the use of OFFSET(1,-1,0) <> 0:
First let's try to understand what OFFSET does? It basically Pulls or Pushes the numbers across the timescale. There are three parameters that are needed in the Syntax OFFSET(x,n,z) where x is the source line item to offset n is the offset value z is fill value if the result is outside the timescaleResult matches the data format of x - meaning it can be number, boolean or anything else.FORMULA: OFFSET(1,-1,0) = 0If you take a look at the left hand side of the formula OFFSET(1,-1,0) it basically throws an output of 1 in all the time periods except the first time period. That is because you are hard coding your first parameter to 1 and then you are asking Anaplan to Push it further by 1 period in the second parameter. Hence the first parameter which is 1 gets pushed to subsequent periods.If you look at the overall formula now OFFSET(1,-1,0) = 0 it checks the condition and looks for a time period which has 0 in it and matches with that time period. Now Let's take a look at Second parameter. Here the ask was to find out the first period of the timescale hence second parameter was kept -1. If the ask is to find out first 3 periods of the timescale you can change the second parameter from -1 to -3 ( Its minus because we have to push the values to subsequent periods) Note: First Parameter doesn't necessarily has to be 1, it can be any number apart from 0
First let's try to understand what OFFSET does? It basically Pulls or Pushes the numbers across the timescale. There are three parameters that are needed in the Syntax
OFFSET(x,n,z) where x is the source line item to offset
n is the offset value
z is fill value if the result is outside the timescale
Result matches the data format of x - meaning it can be number, boolean or anything else.
Result matches the data format of x - meaning it can be number, boolean or anything else
FORMULA: OFFSET(1,-1,0) = 0
If you take a look at the left hand side of the formula OFFSET(1,-1,0) it basically throws an output of 1 in all the time periods except the first time period. That is because you are hard coding your first parameter to 1 and then you are asking Anaplan to Push it further by 1 period in the second parameter. Hence the first parameter which is 1 gets pushed to subsequent periods.
OFFSET(1,-1,0)
1
If you look at the overall formula now OFFSET(1,-1,0) = 0 it checks the condition and looks for a time period which has 0 in it and matches with that time period.
OFFSET(1,-1,0) = 0
Now Let's take a look at Second parameter. Here the ask was to find out the first period of the timescale hence second parameter was kept -1. If the ask is to find out first 3 periods of the timescale you can change the second parameter from -1 to -3 ( Its minus because we have to push the values to subsequent periods)
Note: First Parameter doesn't necessarily has to be 1, it can be any number apart from 0
Note:
Hope that helped!
@Himanshu1998
As Bruno also mentioned, it seems you don't have "1st forecast year" line item in your module. You'd need to create it in this module.
Has anyone experienced this? I have two models of similar size. Both models sum up to 110Gb (57Gb and 53Gb respectively). Models are responsive if you only have one of them open. But the moment you attempt to have them open at the same time all models in the workspace become non responsive. Eventually you get the timeout…
I get the undefined_onFileChange error on uploads. I get the error on every item I try to upload(Lists, Modules) I have tried the following: Refreshed Browser Cleared Caches Changed browsers Restarted machine Redefining the file Recreating the file Changing the file type I probably tried some other things also. Anything…
Hi, we need to bulk export approximately 150 customer Management Reports as PDFs each month from Anaplan. It involves selecting each customer from the context selector, exporting to pdf and then renaming the file. Currently this is a manual process. Has anyone implemented an automated solution to bulk export Management…
